In many cases, in fact, a lot of environmental governance as well as sewage treatment and even clean up some digesters, often can not be separated suction truck. So, suction truck Vacuum pump is a core structure of the suction truck, which is equivalent to the heart of the person. Therefore, in many cases, there are still some operations that are critical to the care and maintenance of suction truck vacuum pumps. Then, the operation principle of the suction truck vacuum pump and the maintenance problems that need attention in the debugging process and the subsequent faults are explained.
The first point that needs to be understood is that, for suction pump vacuum pumps, the centrifugal force of the rotor must first be measured during the installation and commissioning process, depending on whether the centrifugal force is large enough. It is also necessary to see whether the rotor and the rotor are sufficiently close to the inner wall of the suction truck vacuum pump to move. This is also a principle of investigation, and it is also crucial that the tightness of the gas tanks needs to be fully examined. Because if there is any air leakage from the gas chamber, then the state of vacuuming will be greatly reduced and reduced. Therefore, in many cases, in the later period of maintenance and repair, the power take-off device for the vacuum pump of the suction truck, the inside and the inner wall of the vehicle frame, the rotor, the rotating sheet, and the like all require a full range of maintenance and maintenance. Caixing. And need to know that there is an angle between the axis of the suction pump vacuum pump and the axis of rotation of the power tool, so the angle can not exceed seven degrees, which is also a matter to be fully examined in the process of repair and maintenance. .
In the process of installation, commissioning and maintenance, it is necessary to know that the oil and gas separation system needs to be installed at the inlet end of the oil body above the vacuum rod. Well, at this time, the oil outlets often need to be kept at room temperature, neither too high nor too low. Because if the temperature is too high, it will cause the gas to expand and evaporate, and if the temperature is too low, it will be fully blocked in the circulation pipe. In this case, the circulation pipeline will be fully blocked. Therefore, it is necessary to maintain the smoothness of the oil pipeline at all times. At this time, it should be noted that the pipeline needs to be dredged after the first 50 hours of operation, and if necessary, it is necessary to add lubricating oil for cleaning.
There is one point to note here is that it is often necessary to determine whether the total amount of oil is in place, whether it is on the tick mark, and whether the quality of the fluid is normal, and whether the color of the oil body is transparent, or milky, etc. Make adjustments and frequent tests. Another important point to be aware of is that in the water vapor separation system, the isolated water body needs to be stored inside the container. At this time, it should be noted that the liquid is often discharged, and if there is no regular discharge, it will have a negative impact on the gas.
High-efficiency Air Compressor
Screw Air Compressor (working principle) :
Screw compressor is a volumetric gas compression machine with working volume for rotary motion. The compression of gas depends on the change of volume, and the change of volume is achieved by the rotary motion of a pair of rotors in the housing of the compressor. Basic structure: in the body of the compressor, a pair of helical rotors are arranged in parallel to each other. Usually, the rotor with convex teeth outside the section circle is called the Yang rotor or Yang screw. The rotor with concave teeth in the section circle is called Yin rotor or Yin screw, a Yang rotor is connected with the prime mover, driven by the Yang rotor Yin rotor rotor rotation on the last pair of bearings to achieve axial positioning, and bear the axial force in the compressor. Cylindrical roller bearings at both ends of the rotor enable the rotor to achieve radial positioning and withstand radial forces in the compressor. At both ends of the compressor body, a certain shape and size of the orifice are respectively opened. One for inhalation, called the air inlet; The other is used for exhaust, called exhaust port.
Product advantages:
1. Screw Air Compressor works smoothly, has small vibration and low noise compared with piston machine.
2, oil and gas separator: filter material, high efficiency, air oil content rate is less than 2ppm.
3, controller: operation and related data are displayed on the control panel, easy and convenient operation.
4, spraying lubricating oil with sealing, cooling, noise reduction and lubrication.
5, high stability, high efficiency, small vibration, low noise advantages.
6. Good heat dissipation system. Adopting plate-fin structure and material, the cooler has high pressure resistance, high heat dissipation efficiency and good corrosion resistance.
7, Air Filter : heavy duty, multi-stage air filter, large working face.
High-Efficiency Air Compressor,High Efficiency Compressor,High Efficiency Rotary Compressor,High Output Air Compressors
Yangzhou Mustang Air Compressor Co. , Ltd , https://www.aircompressor-ym.com