High Efficiency Two Stage EPS/EPE/XPS/PS Foam Recycling Pelletizing Machine

Pictures of the production line



The two-stage pelletizing system applied in the re-pelletizing job, which consists of two sets of single screw extruder, in case that recycles are with heavy required higher pelletizing output. The ACSS series compacting and pelletizing system combines function of crushing, compacting, plasticization and pelletizing to one step. ACSS system is a reliable and efficiency solution for plastics films, raffias, filaments, bags, woven bags and foaming materials re-pelletizing.

Final productions produced by ACSS system are in the form of pellets/ granules, can directly put into the production line for film blowing, pipe extrusion and plastics injection, etc.

Specifications:

 
Working steps of ACSS compacting and pelletizing system



1. Feeding: as standard design, plastic scraps such as film, filament, raffias conveyed into the compacting room through belt conveyor; to handle rolls' scraps, roll hauling off device is an optional feeding method. Motor drives of conveyor belt and hauling device cooperate with ABB inverter. Feeding speed of conveyor belt or roll hauling off is fully automatic based on how full the compactor's room is. Metal detector can be combined with belt conveyor, and can interlock with control system, to warn and stop the system, in case that metal is found in feeding section.


2. Crushing and compacting: the rotatory blades of compactor will cut up incoming scraps. Frictional heating which caused by high speed rotatory blades will heat and let scraps shrinking just below their agglomerating point. Optimal designed guide structure compacts the material and directs it into extruder screw. Crushes, dries and compacts the material which enables a fast and stable feeding from the compactor directly into the extruder.


3. Plasticization and degassing: A specialized single screw extruder applied to gently melt the pre-compacted material. The plastic scraps will be well melted, plasticized in the first stage extruder, and the plastic will be extrude by the second stage extruder. With double-zone vacuum degassing system, volatiles such as low molecular and moisture will be removed efficiency, especially suitable to heavy printed film and material with some water content.


4. Melt filtration: Segmented filtering principle, fore filtering in the first extruder, and fine filtering in the second extruder, to reduce the frequency of filtering sieves changing. The requirements on the filter technology depend heavily on the quality of the input material as well as the planned use of granules.


5. Pelletizing: die-face water ring pelletizing system set as the standard granulating method in ACSS system. Self-adjusting pelletizing head for the best granulate quality and long uptime thanks to consistently correct blades pressure. RPM of rotatory blades is automatic based on melt extruding pressure. Advanced dewatering vibration sieve combining with horizontal-type centrifugal dewatering present high performance dried pellets.
 
Main technical parameter:
  
Advantages of ACSS compacting and pelletizing system
1. Combine crushing, compacting and pelletizing steps in one system, less-labor cost;
2. Higher efficiency feeding, suitable to film, filament, raffia, foaming materials;
3. Higher output and lower energy consumption.
4. Because of separated filtering system in two-stage extruder, system can realize steady extrusion job.
5. Second stage's extruder can present low temperature extrusion, which can guarantee the final production's quality.

Why choose us
1. Lower investment cost for a high quality and durable machine;

2. Low energy consumption with high production output;

3. Overseas installation and training are available;

4. Machine warranty with spares in stocking and in-time delivery;

5. Fast machine delivery and installation: AceRetech produces on an average of 10 sets of plastic machines per month and can deliver the machine faster than most manufacturers. The regular delivery time of an AceRetech recycling machine is 60 days.

The open working platform is convenient for the placement of processing materials, and can be applied to the processing of large format materials with large size honeycomb adsorption platform. Such as: footwear, clothing industry, foam, sponge, advertising, sheet metal, etc., and meet the needs of the model industry, handicrafts industry, bamboo products industry and other small industries. Optional with automatic focus, red light positioning and other functions, so that the machine is perfect, its function to the extreme. Achieve multifunction, time saving and high efficiency.

 

the work table size:	1220mm X 1220mm cutting X 3000mm
X axis cutting stroke	3000mm
Y axis travel	1220mm
rotate speed	0-6000mm/min
system resolution	+ 0.04
file format	G code
worktable structure	thickening square tube welding
working voltage	AC220V/20HZ

Foam Machine

Foam Machine,Foam Engraving Machine,Foam Cutting Machine,Carving Foam Machine

JINAN HT MACHINERY CO.,LTD , https://www.jncncrouter.com