Do you work with steel in your manufacturing facility? If so, you know all about watching your expensive steel scrap, processing fluids and facility floor space disappear.
Whether it's turnings, chips, filings, shavings or sludge, a steel briquetting machine from ShengBo is the solution. Steel briquetting can double the value you get, cause steel briquettes are easier to manage, transport, sell and recycle.
We recommend you a fully-automatic steel briquetting line, with conveyor, bunker, elevator, etc. Our Y83W horizontal briquette machine has advantages as follows:
1) scraps length can be less than 10cm.
2) especially suitable for hard metal like stainless steel chips, grade 7 and grade 12 aluminum scrap, long copper chips, etc.
3) make storage area clean and green.
4) much lower than vertical one, suit the workshop with low height.
Â
| model | Y83W-2500 |
| nominal force | 2500kn |
| briquette diameter | D90Â |
| briquette density | ≥ 5t/m³ |
| briquette weight | 2~3kg |
| productivity | 3~4block/min |
| output in one shift | 3~4t/8h |
| total power | 22kw |
| machine weight | about 4.5ton |
| overall dimension | host machine: 3800*690*2000mm oil tank: 1350*1300*1160mm |
Â
Â
Â
Do you work with steel in your manufacturing facility? If so, you know all about watching your expensive steel scrap, processing fluids and facility floor space disappear.
Whether it's turnings, chips, filings, shavings or sludge, a steel briquetting machine from ShengBo is the solution. Steel briquetting can double the value you get, cause steel briquettes are easier to manage, transport, sell and recycle.
We recommend you a fully-automatic steel briquetting line, with conveyor, bunker, elevator, etc. Our Y83W horizontal briquette machine has advantages as follows:
1) scraps length can be less than 10cm.
2) especially suitable for hard metal like stainless steel chips, grade 7 and grade 12 aluminum scrap, long copper chips, etc.
3) make storage area clean and green.
4) much lower than vertical one, suit the workshop with low height.
Â
| model | Y83W-2500 |
| nominal force | 2500kn |
| briquette diameter | D90Â |
| briquette density | ≥ 5t/m³ |
| briquette weight | 2~3kg |
| productivity | 3~4block/min |
| output in one shift | 3~4t/8h |
| total power | 22kw |
| machine weight | about 4.5ton |
| overall dimension | host machine: 3800*690*2000mm oil tank: 1350*1300*1160mm |
Â
Â
Â
BT Light Shrink Fit Tool Holder
1. High precision, large clamping surface, good dynamic travel. Fine dynamic balance G2.5 / G6.3 selection.
2. There is no clearance after clamping the tool, and chips, coolant and dust will not enter.
3. The slope is very light and thin, try to avoid interference with the workpiece.
4. The tool has the shortest highlight, high rigidity, firm and stable clamping, and high precision.
Sintered handle, sintered handle features, heat expansion type shrinkage handle, heat shrinkage type BT handle, sintered type BT handle:
5. Small tool deflection, reduce tool wear, reduce tool cost
6. The tool life can be extended by 2-5 times.
7. Suitable for high-speed cutting.
8. Better precision
9. Under the same precision condition, the cutter can be greatly increased for deep cutting. There are many types of knife handles, such as 7:24 taper, HSK and so on are the connection mode between the knife handle and the machine tool, each knife handle type (BT type, HSK type) has the type of heat expansion and cold contraction fastening knife handle, heat expansion and cold contraction refers to the connection mode between the knife handle and the tool. 5, the principle of heat up and cold down, than the general way of tool holding more accurate yaw precision.
Shrink Fit Holder,High Precision Tool Holder,Bt Light Shrink Fit Tool Holder,Bt Light Shrink Fit Tool Holder
Shandong Chongde Precision Machinery Co.,LTD , https://www.springcollet.com