Content: Three eccentric metal seal butterfly valve with high temperature, light operation, open and close without friction, closed with the torque transmission mechanism to compensate for increased sealing, improved butterfly valve sealing performance and extend the life of the advantages. But there are still structural problems. At present, as a component used to realize on-off and flow control of pipeline system, it has been widely used in many fields such as petroleum, chemical industry, metallurgy, hydropower and so on. In the known butterfly valve technology, the dense use of multi-seal structure, the sealing material is rubber, and so on. Due to the structural characteristics of the restrictions, do not meet the high temperature, high pressure and corrosion-resistant, anti-wear and other industries. A more advanced butterfly valve is a three-eccentric metal seal butterfly valve, the valve body and the valve seat as a single component, seat sealing surface layer surfacing temperature, corrosion resistant alloy material. Multi-layer soft stacked ring fixed to the valve plate, this butterfly valve compared with the traditional butterfly valve with high temperature, light operation, opening and closing without friction, closed with the torque of the transmission mechanism to compensate for increased sealing, improved butterfly valve The sealing performance and extend the service life of the advantages. Three Eccentric Metal Sealing Butterfly Valve Structural Features Three Eccentric Metal Sealing Butterfly Valve Butterfly Center of Rotation (ie, the valve shaft center) and the butterfly valve seal surface to form a size A bias and the valve body centerline to form a B bias; Import measurement The valve body seal surface centerline and valve seat centerline (ie, valve body centerline) form an angle β angle. However, this butterfly valve in the course of the following problems still exist: First, the multi-layer hard and soft stacked ring is fixed to the valve plate, the valve normally open state when the medium seals Surface formation of positive erosion, sheet metal sandwich in the soft seal by erosion, a direct impact on sealing performance. Second, by the structural conditions of the structure does not adapt to do the following DN200 valve, because the overall structure of the valve plate is too thick, large flow resistance. Third, due to the principle of three eccentric structure, the seal between the sealing surface of the valve plate and the valve seat is pressed against the valve seat by the torque of the transmission device. The positive flow state, the higher the media pressure seal squeeze tight. When the flow medium countercurrent media pressure increases with the pressure between the valve plate and valve seat unit pressure is less than the medium pressure, the seal began to leak. High-performance three eccentric two-way hard sealing butterfly valve, characterized in that: the seat ring seal by the soft T-ring multi-layer stainless steel sheet on both sides. The sealing surface of the valve plate and the valve seat is an oblique conical structure, and a temperature-resistant and corrosion-resistant alloy material is deposited on the oblique conical surface of the valve plate; the spring fixed between the adjusting ring plate and the adjusting bolt on the pressure plate is arranged together. This structure effectively compensates for the tolerance band between the sleeve and the valve body and the elastic deformation of the valve stem under the medium pressure and solves the sealing problem existing in the process of transporting the valve in the bidirectional interchangeable medium. The soft T-shaped multi-layer stainless steel sheet on both sides of the seal ring, with the advantages of both metal seal and soft seal, both in low temperature and high temperature conditions, have zero leakage of sealing performance. Experiments show that pool positive flow state (medium flow direction and disk rotation in the same direction), the sealing surface pressure is the torque of the actuator and the medium pressure on the role of the valve plate. Positive media pressure increases when the valve plate oblique cone surface and seat sealing surface squeeze the more tight, the better the sealing effect. In counter-current conditions, the seal between the valve plate and the valve seat presses the valve plate against the valve seat due to the moment of the drive. As the pressure of the reverse medium increases, the positive pressure between the valve plate and the valve seat is less than the pressure of the medium. The deformation stored by the spring of the adjusting ring after the load is absorbed can compensate for the tight pressure on the sealing surface of the valve plate and the valve seat Play a role in automatic compensation. Therefore, unlike the prior art, the utility model has the advantages that the soft and hard multi-layer sealing ring is mounted on the valve plate and is directly mounted on the valve body, and an adjusting ring is provided between the pressing plate and the valve seat which is a perfect bidirectional hard sealing method . It will replace gate valves, globe valves and ball valves. More keyword search: butterfly valve
Tungsten Carbide Powder
Tungsten carbide thermal spray powder is a type of powder material that is used in thermal spray processes. It is composed of tungsten carbide particles, which are combined with a binder material to form a powder.
Thermal spraying is a coating process that involves heating the powder material to a molten or semi-molten state and then spraying it onto a surface to create a protective or functional coating. Tungsten carbide thermal spray powder is known for its hardness, wear resistance, and high melting point, making it suitable for applications where extreme wear or high temperatures are present.
The tungsten carbide particles in the powder provide the coating with excellent wear resistance, while the binder material helps to bind the particles together and adhere them to the surface. The powder can be sprayed using various thermal spray techniques, such as flame spraying, plasma spraying, or high-velocity oxy-fuel spraying.
Tungsten carbide thermal spray coatings are commonly used in industries such as aerospace, automotive, oil and gas, and mining, where components are exposed to harsh environments or abrasive conditions. These coatings can provide protection against wear, erosion, corrosion, and high temperatures, extending the lifespan of the coated components.
Tungsten Carbides,Tungsten Carbide Powder,Tungsten Carbide Coating,HVOF Tungsten Carbide Coating
Luoyang Golden Egret Geotools Co., Ltd , https://www.xtcalloypowder.com