The magnetic chip remover of the machine tool mainly uses the magnetic force of the strong magnetic field generated by the permanent magnet material to adsorb the chip on the working magnetic plate of the chip removing machine, or the particles, powder and the length in the oil and the emulsion are less than or equal to 150 Millimeters of iron scrap are separated by suction and transported to a designated chip removal point or a collection box. It can handle powdery, granular and iron scraps less than 100mm in length and non-scraps, or separate the oil and emulsion from the debris and transport them to the designated hopper.
Machine magnetic chip remover working principle introduction:
Where magnets have the properties of iron absorption, while the power of iron absorption ends. Both ends are called magnetic poles. Any magnet has a north-south orientation. One end of the north refers to the North Pole, which is denoted by “Nâ€. One end of the guide is called the South Pole and is denoted by “Sâ€. When two magnets are close together, they will repel each other if they are the same pole; if they are different poles, they will attract each other. The range that magnetic force can reach is called magnetic field. Magnetic chip remover is to adsorb the chips on the working magnetic board of the chip remover, or to adsorb and separate the iron particles in the oil, the emulsion in the form of particles, powder and the length of ≤ 150 mm, and transport them to the specified chip removal. Location or collection box. It can handle powdery, granular and iron scraps less than 100mm in length and non-scraps, or separate the oil and emulsion from the debris and transport them to the designated hopper.
Machine magnetic chip remover use note:
1, semi dry iron scraps should pay attention. Machine magnetic chip remover is particularly difficult for such iron scraps. The usual way is to completely turn this type of iron into wet, and then design the chip remover as a wet process. In chip evacuation systems, coolants are sometimes treated separately and are not allowed to mix in the swarf.
2. The chip removal capacity of the magnetic chip remover is not as good as possible. The main reason for the impact on the amount of chips is the rotation speed, the effective chip width, the distance between the magnetic blocks or the span of the scraper. Under the condition that the width and spacing of the row (specification and model) are constant, the speed of lifting determines the size of the chips, so Debris removal increases wear.
3, strip magnetic, crawler chain chip remover each power head can achieve 42m no overlap, but taking into account the actual installation, generally does not exceed 30m, beyond this range to increase the power head. The maximum length of other types is limited (except for large flow rate).
Machine magnetic chip remover working principle introduction:
Where magnets have the properties of iron absorption, while the power of iron absorption ends. Both ends are called magnetic poles. Any magnet has a north-south orientation. One end of the north refers to the North Pole, which is denoted by “Nâ€. One end of the guide is called the South Pole and is denoted by “Sâ€. When two magnets are close together, they will repel each other if they are the same pole; if they are different poles, they will attract each other. The range that magnetic force can reach is called magnetic field. Magnetic chip remover is to adsorb the chips on the working magnetic board of the chip remover, or to adsorb and separate the iron particles in the oil, the emulsion in the form of particles, powder and the length of ≤ 150 mm, and transport them to the specified chip removal. Location or collection box. It can handle powdery, granular and iron scraps less than 100mm in length and non-scraps, or separate the oil and emulsion from the debris and transport them to the designated hopper.
Machine magnetic chip remover use note:
1, semi dry iron scraps should pay attention. Machine magnetic chip remover is particularly difficult for such iron scraps. The usual way is to completely turn this type of iron into wet, and then design the chip remover as a wet process. In chip evacuation systems, coolants are sometimes treated separately and are not allowed to mix in the swarf.
2. The chip removal capacity of the magnetic chip remover is not as good as possible. The main reason for the impact on the amount of chips is the rotation speed, the effective chip width, the distance between the magnetic blocks or the span of the scraper. Under the condition that the width and spacing of the row (specification and model) are constant, the speed of lifting determines the size of the chips, so Debris removal increases wear.
3, strip magnetic, crawler chain chip remover each power head can achieve 42m no overlap, but taking into account the actual installation, generally does not exceed 30m, beyond this range to increase the power head. The maximum length of other types is limited (except for large flow rate).
Flat Flange,Steel Flange Plate,Pipe Plate Flange,Alloy Steel Plate Flange
SHANXI BAOFAN HEAVY INDUSTRY GROUP CO., LTD , https://www.baofanflanges.com